Date   

Re: NVDA Speech delay after Computer is Idle

Betsy Grenevitch
 

Thank you for such specific step by step instructions. If it does it again I will try the steps on this laptop. So far this afternoon it has not done it and i have left it sitting for a couple of hours again. Just maybe something corrected in the system on its own. That would be great if that is the situation.

On 9/25/2020 6:57 PM, Shaun Everiss wrote:
I had this weird issue happen with latest waterfox, cpu racing and the like for ages.

I suggest go through the steps from your computer manufacturer's site to perform a nondestructive reset on your ram.

I just updated firmware on windows for all the hp systems I have.

The fans raced things didn't work right, etc.

I was able to reset the unit.

Generally with a system like a desktop with only a power button, pull out the power and remove any disks, and other hardware.

Then just hold down power or reset for 5-15 seconds, then plug power and keyboard in, then turn everything on, you may have to hit enter to get it to start.

Then everything just works and you plug things in.

With laptops, pull out the battery, and hold power for 15 seconds, put battery in, plug things back in and turn on.

If sealed, do everything as above and don't remove battery.

So far the system has not gone fluffy yet.

Just make sure all drivers and firmware are updated to latest and it works.



On 26/09/2020 1:35 am, Betsy Grenevitch wrote:
This problem with NVDA began after my latest windows update. Sometimes it will happen even when I am in the middle of doing something like saving a document.


I read Jonathan's article but it is above my understanding of how to handle the situation.

On 9/24/2020 10:45 AM, Gene wrote:
I don't know why that is.  that appears to indicate a different problem than the one I pointed to.

Gene
-----Original Message----- From: Mária Orovčíková
Sent: Thursday, September 24, 2020 8:13 AM
To: nvda@nvda.groups.io
Subject: Re: [nvda] NVDA does not work properly

Hello again,
the thing is that it also happens when a sound is playing (for example
video or audio), it takes some time til NVDA starts working again after
not being active.
Maria

On 24. 9. 2020 14:28, Gene wrote:
If a computer has this problem, while this is unusual, in generel the problem occurs when the computer isn't used for a much shorter time, this page mauy have the solution.
https://mosen.org/soundsfrustrating/

You may want to read the article or skip to the part that discusses the specific solution I have in mind.  To find the beginning of that specific section, search for
Thanks so much to

Gene
-----Original Message----- From: Mária Orovčíková
Sent: Thursday, September 24, 2020 7:00 AM
To: nvda@nvda.groups.io
Subject: [nvda] NVDA does not work properly

Hello list,
I have some weird issue with NVDA.
When I do not use my laptop for a longer period of time (half an hour
and longer), but the laptop is stil on, and when I want to use it again,
I pres any key, NVdA takes quite a long time to start speaking.
I have Lenovo, Windows 10, latest NVDA version and I have screensavers,
and standby mode disabled.
Please, if anyone knows any workaround, let me know.
Thank you very much for your help.
Maria


















--
Betsy Grenevitch
678-862-3876


Re: NVDA Speech delay after Computer is Idle

 

I had this weird issue happen with latest waterfox, cpu racing and the like for ages.

I suggest go through the steps from your computer manufacturer's site to perform a nondestructive reset on your ram.

I just updated firmware on windows for all the hp systems I have.

The fans raced things didn't work right, etc.

I was able to reset the unit.

Generally with a system like a desktop with only a power button, pull out the power and remove any disks, and other hardware.

Then just hold down power or reset for 5-15 seconds, then plug power and keyboard in, then turn everything on, you may have to hit enter to get it to start.

Then everything just works and you plug things in.

With laptops, pull out the battery, and hold power for 15 seconds, put battery in, plug things back in and turn on.

If sealed, do everything as above and don't remove battery.

So far the system has not gone fluffy yet.

Just make sure all drivers and firmware are updated to latest and it works.

On 26/09/2020 1:35 am, Betsy Grenevitch wrote:
This problem with NVDA began after my latest windows update. Sometimes it will happen even when I am in the middle of doing something like saving a document.


I read Jonathan's article but it is above my understanding of how to handle the situation.

On 9/24/2020 10:45 AM, Gene wrote:
I don't know why that is.  that appears to indicate a different problem than the one I pointed to.

Gene
-----Original Message----- From: Mária Orovčíková
Sent: Thursday, September 24, 2020 8:13 AM
To: nvda@nvda.groups.io
Subject: Re: [nvda] NVDA does not work properly

Hello again,
the thing is that it also happens when a sound is playing (for example
video or audio), it takes some time til NVDA starts working again after
not being active.
Maria

On 24. 9. 2020 14:28, Gene wrote:
If a computer has this problem, while this is unusual, in generel the problem occurs when the computer isn't used for a much shorter time, this page mauy have the solution.
https://mosen.org/soundsfrustrating/

You may want to read the article or skip to the part that discusses the specific solution I have in mind.  To find the beginning of that specific section, search for
Thanks so much to

Gene
-----Original Message----- From: Mária Orovčíková
Sent: Thursday, September 24, 2020 7:00 AM
To: nvda@nvda.groups.io
Subject: [nvda] NVDA does not work properly

Hello list,
I have some weird issue with NVDA.
When I do not use my laptop for a longer period of time (half an hour
and longer), but the laptop is stil on, and when I want to use it again,
I pres any key, NVdA takes quite a long time to start speaking.
I have Lenovo, Windows 10, latest NVDA version and I have screensavers,
and standby mode disabled.
Please, if anyone knows any workaround, let me know.
Thank you very much for your help.
Maria

















Re: Spelling corrections not displayed when composing a message in Microsoft teams for windows

Luke Robinett <blindgroupsluke@...>
 

Thank you for checking and replying! I will give it another shot when I’m back at work next week and see if the issue has improved. That would be awesome. Take care.

On Sep 24, 2020, at 4:25 AM, Rui Fontes <rui.fontes@tiflotecnia.com> wrote:

Hello!


Last week I have tried with a costummer and the result was the same...

Today I have tested and the context menu have worked as expected...

Some changes in Teams itself? I don't know...


Rui Fontes

NVDA portuguese team


Às 03:13 de 24/09/2020, Luke Robinett escreveu:
Anyone? Just curious if anyone is able to reproduce what I described in this email. Let me know if you need more info. Thanks.

On Sep 21, 2020, at 12:58 PM, Luke Robinett via groups.io <blindgroupsluke=gmail.com@groups.io> wrote:
Hi folks,

When I am typing a message in Microsoft teams, NVDA announces misspelled words, as expected, but when I hit the right windows key to get the Context menu, I don’t get any spelling suggestions like I would in other Microsoft apps. I will say I attempted this same thing with narrator and encountered the same problem, so it might be an issue with Teams. Just thought I’d see if anyone else has experienced this and if there are any workarounds. Thanks.








Re: NVDA Speech delay after Computer is Idle

Betsy Grenevitch
 

I have no idea how to get there and this just started recently. However, it is sporadic. I left the computer on and was gone for almost three hours and it worked as soon as I touched it when I came back. It is really strange.


On 9/25/2020 10:28 AM, Chris via groups.io wrote:

Sounds like a power management issue

Possibly because  your hard drive is going to sleep, the delay may well be because you are using a mechanical HDD drive ,

 

Rather than a solid state SSD drive

 

You can prevent your hard drive going to sleep through your advanced power plan settings

 

 

 

From: Betsy Grenevitch
Sent: 25 September 2020 14:39
To: nvda@nvda.groups.io
Subject: Re: [nvda] NVDA Speech delay after Computer is Idle

 

If it is the computer going to sleep how do you wake it up? Is there a setting that may have gotten changed with the latest Windows update. I did not have this problem until then.

-- 
Betsy Grenevitch
678-862-3876


Re: Station playlist

Afik Souffir <afik.souffir@...>
 

 

Thanks, I did subscribed to it and I do have the dev version.

 

Thanks!

 

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Joseph Lee
Sent: Friday, September 25, 2020 9:26 PM
To: nvda@nvda.groups.io
Subject: Re: [nvda] Station playlist

 

Hi,

Go to community add-ons website, select StationPlaylist, and download the development version. Also, subscribe to NvDA-SPL list located at:

https://nvda-spl.groups.io/g/nvda-spl

Usually I do not announce development build announcements on this list so folks will not be overwhelmed. Note that these development builds are really bleeding-edge builds, sometimes requiring most recent NVDA stable version (or in some cases, beta or even alpha releases). I’ll make an important announcement about development builds as part of an upcoming SPL add-on release announcement.

Cheers,

Joseph

 

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Afik Souffir
Sent: Friday, September 25, 2020 11:23 AM
To: nvda@nvda.groups.io
Subject: Re: [nvda] Station playlist

 

 

How can I test the add on?

 

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Joseph Lee
Sent: Friday, September 25, 2020 9:20 PM
To: nvda@nvda.groups.io
Subject: Re: [nvda] Station playlist

 

Hi,

To name an encoder, when an encoder is focused, press Alt+NVDA+0 to open encoder settings dialog for the selected encoder. The first option will be “encoder label” and you can use this field to label your encoder whatever you like. To remove an encoder label, go to the encoder with the label you wish to delete, press Alt+NVDA+0, then delete whatever is shown on “encoder label” field.

In the past an encoder labeler command was provided (F12) to open a dialog dedicated to labeling encoders. This was removed in a recent add-on release. F12 command is coming back this November to open encoder settings dialog (currently being tested by our testers).

Cheers,

Joseph

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Robert Doc Wright godfearer
Sent: Friday, September 25, 2020 11:14 AM
To: nvda@nvda.groups.io
Subject: [nvda] Station playlist

 

how do you name an encoder using NVDA?

******
If we can't look at ourselves, and ask, why?  then where does the learning start?

 

Family times where there is fun for every ear!
http://stream.wrighthere.net:8000/stream.mp3

 

Or ask your A device to play Family times on tuneIn
You can also find us on your mobile device install OoTunes and search for Family times


Re: Station playlist

 

Hi,

Go to community add-ons website, select StationPlaylist, and download the development version. Also, subscribe to NvDA-SPL list located at:

https://nvda-spl.groups.io/g/nvda-spl

Usually I do not announce development build announcements on this list so folks will not be overwhelmed. Note that these development builds are really bleeding-edge builds, sometimes requiring most recent NVDA stable version (or in some cases, beta or even alpha releases). I’ll make an important announcement about development builds as part of an upcoming SPL add-on release announcement.

Cheers,

Joseph

 

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Afik Souffir
Sent: Friday, September 25, 2020 11:23 AM
To: nvda@nvda.groups.io
Subject: Re: [nvda] Station playlist

 

 

How can I test the add on?

 

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Joseph Lee
Sent: Friday, September 25, 2020 9:20 PM
To: nvda@nvda.groups.io
Subject: Re: [nvda] Station playlist

 

Hi,

To name an encoder, when an encoder is focused, press Alt+NVDA+0 to open encoder settings dialog for the selected encoder. The first option will be “encoder label” and you can use this field to label your encoder whatever you like. To remove an encoder label, go to the encoder with the label you wish to delete, press Alt+NVDA+0, then delete whatever is shown on “encoder label” field.

In the past an encoder labeler command was provided (F12) to open a dialog dedicated to labeling encoders. This was removed in a recent add-on release. F12 command is coming back this November to open encoder settings dialog (currently being tested by our testers).

Cheers,

Joseph

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Robert Doc Wright godfearer
Sent: Friday, September 25, 2020 11:14 AM
To: nvda@nvda.groups.io
Subject: [nvda] Station playlist

 

how do you name an encoder using NVDA?

******
If we can't look at ourselves, and ask, why?  then where does the learning start?

 

Family times where there is fun for every ear!
http://stream.wrighthere.net:8000/stream.mp3

 

Or ask your A device to play Family times on tuneIn
You can also find us on your mobile device install OoTunes and search for Family times


Re: Station playlist

Afik Souffir <afik.souffir@...>
 

 

How can I test the add on?

 

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Joseph Lee
Sent: Friday, September 25, 2020 9:20 PM
To: nvda@nvda.groups.io
Subject: Re: [nvda] Station playlist

 

Hi,

To name an encoder, when an encoder is focused, press Alt+NVDA+0 to open encoder settings dialog for the selected encoder. The first option will be “encoder label” and you can use this field to label your encoder whatever you like. To remove an encoder label, go to the encoder with the label you wish to delete, press Alt+NVDA+0, then delete whatever is shown on “encoder label” field.

In the past an encoder labeler command was provided (F12) to open a dialog dedicated to labeling encoders. This was removed in a recent add-on release. F12 command is coming back this November to open encoder settings dialog (currently being tested by our testers).

Cheers,

Joseph

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Robert Doc Wright godfearer
Sent: Friday, September 25, 2020 11:14 AM
To: nvda@nvda.groups.io
Subject: [nvda] Station playlist

 

how do you name an encoder using NVDA?

******
If we can't look at ourselves, and ask, why?  then where does the learning start?

 

Family times where there is fun for every ear!
http://stream.wrighthere.net:8000/stream.mp3

 

Or ask your A device to play Family times on tuneIn
You can also find us on your mobile device install OoTunes and search for Family times


Re: Station playlist

 

Hi,

To name an encoder, when an encoder is focused, press Alt+NVDA+0 to open encoder settings dialog for the selected encoder. The first option will be “encoder label” and you can use this field to label your encoder whatever you like. To remove an encoder label, go to the encoder with the label you wish to delete, press Alt+NVDA+0, then delete whatever is shown on “encoder label” field.

In the past an encoder labeler command was provided (F12) to open a dialog dedicated to labeling encoders. This was removed in a recent add-on release. F12 command is coming back this November to open encoder settings dialog (currently being tested by our testers).

Cheers,

Joseph

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Robert Doc Wright godfearer
Sent: Friday, September 25, 2020 11:14 AM
To: nvda@nvda.groups.io
Subject: [nvda] Station playlist

 

how do you name an encoder using NVDA?

******
If we can't look at ourselves, and ask, why?  then where does the learning start?

 

Family times where there is fun for every ear!
http://stream.wrighthere.net:8000/stream.mp3

 

Or ask your A device to play Family times on tuneIn
You can also find us on your mobile device install OoTunes and search for Family times


Station playlist

Robert Doc Wright godfearer
 

how do you name an encoder using NVDA?
******
If we can't look at ourselves, and ask, why?  then where does the learning start?
 
Family times where there is fun for every ear!
http://stream.wrighthere.net:8000/stream.mp3
 
Or ask your A device to play Family times on tuneIn
You can also find us on your mobile device install OoTunes and search for Family times


Re: Nvda And SPL!

Afik Souffir <afik.souffir@...>
 

 

Thanks!!!! It's works now.

 

I'm reading the guide now.

 

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Joseph Lee
Sent: Friday, September 25, 2020 8:45 PM
To: nvda@nvda.groups.io
Subject: Re: [nvda] Nvda And SPL!

 

Hi,

SPL Assistant layer won’t show up unless you open Input Gestures dialog while Studio window is focused. This is because SPL Assistant is defined inside the Studio app module, whereas SPL Controller is part of the SPL Utilities global plugin portion of the add-on.

Cheers,

Joseph

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Afik Souffir
Sent: Friday, September 25, 2020 10:44 AM
To: nvda@nvda.groups.io
Subject: Re: [nvda] Nvda And SPL!

 

 

Hi, there is no spl assistance, there is spl controller.

 

I've just checked.

 

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Joseph Lee
Sent: Friday, September 25, 2020 8:34 PM
To: nvda@nvda.groups.io
Subject: Re: [nvda] Nvda And SPL!

 

Hi,

With Studio window focused, open input gestures dialog (NVDA menu/Preferences/Input gestures), scroll to StationPlaylist category, expand it and look for SPL Assistant, then add a memorable gesture that does not conflict with other NVDA commands.

Cheers,

Joseph

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Afik Souffir
Sent: Friday, September 25, 2020 10:28 AM
To: nvda@nvda.groups.io
Subject: Re: [nvda] Nvda And SPL!

 

How do you assign a keystroke for open it?

 

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Joseph Lee
Sent: Friday, September 25, 2020 8:19 PM
To: nvda@nvda.groups.io
Subject: Re: [nvda] Nvda And SPL!

 

Hi,

That’ll be SPL Assistant layer, D (you must assign a hotkey to open SPL Assistant layer first).

Cheers,

Joseph

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Afik Souffir
Sent: Friday, September 25, 2020 10:16 AM
To: nvda@nvda.groups.io
Subject: Re: [nvda] Nvda And SPL!

 

 

I'm asking the same question

 

How do you know the time in a playlist?

 

 

Afik

 

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Joseph Lee
Sent: Friday, September 25, 2020 7:29 PM
To: nvda@nvda.groups.io
Subject: Re: [nvda] Nvda And SPL!

 

Hi,

Yes, it is like starting from scratch with JAWS. There is a way to “label” encoders using NVDA through an add-on for StationPlaylist (expect a release announcement next week).

Cheers,

Joseph

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Thomas E Williamson, Senior
Sent: Friday, September 25, 2020 4:45 AM
To: nvda@nvda.groups.io
Subject: [nvda] Nvda And SPL!

 

Hello,

I am wanting to use nvda with station playlist 5.40.

Will this be like starting over again in turns of the key strokes from Jaws?

For example, when I open studio, my encoders do not display the names of the radio stations that I previously named.

or is there a tutorial that can assist in this matter?

Hope this make since.

Thanks for your help in advance!

Regards,

Thomas.

 

 

 


Re: Nvda And SPL!

 

Hi,

SPL Assistant layer won’t show up unless you open Input Gestures dialog while Studio window is focused. This is because SPL Assistant is defined inside the Studio app module, whereas SPL Controller is part of the SPL Utilities global plugin portion of the add-on.

Cheers,

Joseph

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Afik Souffir
Sent: Friday, September 25, 2020 10:44 AM
To: nvda@nvda.groups.io
Subject: Re: [nvda] Nvda And SPL!

 

 

Hi, there is no spl assistance, there is spl controller.

 

I've just checked.

 

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Joseph Lee
Sent: Friday, September 25, 2020 8:34 PM
To: nvda@nvda.groups.io
Subject: Re: [nvda] Nvda And SPL!

 

Hi,

With Studio window focused, open input gestures dialog (NVDA menu/Preferences/Input gestures), scroll to StationPlaylist category, expand it and look for SPL Assistant, then add a memorable gesture that does not conflict with other NVDA commands.

Cheers,

Joseph

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Afik Souffir
Sent: Friday, September 25, 2020 10:28 AM
To: nvda@nvda.groups.io
Subject: Re: [nvda] Nvda And SPL!

 

How do you assign a keystroke for open it?

 

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Joseph Lee
Sent: Friday, September 25, 2020 8:19 PM
To: nvda@nvda.groups.io
Subject: Re: [nvda] Nvda And SPL!

 

Hi,

That’ll be SPL Assistant layer, D (you must assign a hotkey to open SPL Assistant layer first).

Cheers,

Joseph

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Afik Souffir
Sent: Friday, September 25, 2020 10:16 AM
To: nvda@nvda.groups.io
Subject: Re: [nvda] Nvda And SPL!

 

 

I'm asking the same question

 

How do you know the time in a playlist?

 

 

Afik

 

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Joseph Lee
Sent: Friday, September 25, 2020 7:29 PM
To: nvda@nvda.groups.io
Subject: Re: [nvda] Nvda And SPL!

 

Hi,

Yes, it is like starting from scratch with JAWS. There is a way to “label” encoders using NVDA through an add-on for StationPlaylist (expect a release announcement next week).

Cheers,

Joseph

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Thomas E Williamson, Senior
Sent: Friday, September 25, 2020 4:45 AM
To: nvda@nvda.groups.io
Subject: [nvda] Nvda And SPL!

 

Hello,

I am wanting to use nvda with station playlist 5.40.

Will this be like starting over again in turns of the key strokes from Jaws?

For example, when I open studio, my encoders do not display the names of the radio stations that I previously named.

or is there a tutorial that can assist in this matter?

Hope this make since.

Thanks for your help in advance!

Regards,

Thomas.

 

 

 


Re: Nvda And SPL!

Afik Souffir <afik.souffir@...>
 

 

Hi, there is no spl assistance, there is spl controller.

 

I've just checked.

 

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Joseph Lee
Sent: Friday, September 25, 2020 8:34 PM
To: nvda@nvda.groups.io
Subject: Re: [nvda] Nvda And SPL!

 

Hi,

With Studio window focused, open input gestures dialog (NVDA menu/Preferences/Input gestures), scroll to StationPlaylist category, expand it and look for SPL Assistant, then add a memorable gesture that does not conflict with other NVDA commands.

Cheers,

Joseph

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Afik Souffir
Sent: Friday, September 25, 2020 10:28 AM
To: nvda@nvda.groups.io
Subject: Re: [nvda] Nvda And SPL!

 

How do you assign a keystroke for open it?

 

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Joseph Lee
Sent: Friday, September 25, 2020 8:19 PM
To: nvda@nvda.groups.io
Subject: Re: [nvda] Nvda And SPL!

 

Hi,

That’ll be SPL Assistant layer, D (you must assign a hotkey to open SPL Assistant layer first).

Cheers,

Joseph

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Afik Souffir
Sent: Friday, September 25, 2020 10:16 AM
To: nvda@nvda.groups.io
Subject: Re: [nvda] Nvda And SPL!

 

 

I'm asking the same question

 

How do you know the time in a playlist?

 

 

Afik

 

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Joseph Lee
Sent: Friday, September 25, 2020 7:29 PM
To: nvda@nvda.groups.io
Subject: Re: [nvda] Nvda And SPL!

 

Hi,

Yes, it is like starting from scratch with JAWS. There is a way to “label” encoders using NVDA through an add-on for StationPlaylist (expect a release announcement next week).

Cheers,

Joseph

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Thomas E Williamson, Senior
Sent: Friday, September 25, 2020 4:45 AM
To: nvda@nvda.groups.io
Subject: [nvda] Nvda And SPL!

 

Hello,

I am wanting to use nvda with station playlist 5.40.

Will this be like starting over again in turns of the key strokes from Jaws?

For example, when I open studio, my encoders do not display the names of the radio stations that I previously named.

or is there a tutorial that can assist in this matter?

Hope this make since.

Thanks for your help in advance!

Regards,

Thomas.

 

 

 


Re: Nvda And SPL!

 

Hi,

With Studio window focused, open input gestures dialog (NVDA menu/Preferences/Input gestures), scroll to StationPlaylist category, expand it and look for SPL Assistant, then add a memorable gesture that does not conflict with other NVDA commands.

Cheers,

Joseph

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Afik Souffir
Sent: Friday, September 25, 2020 10:28 AM
To: nvda@nvda.groups.io
Subject: Re: [nvda] Nvda And SPL!

 

How do you assign a keystroke for open it?

 

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Joseph Lee
Sent: Friday, September 25, 2020 8:19 PM
To: nvda@nvda.groups.io
Subject: Re: [nvda] Nvda And SPL!

 

Hi,

That’ll be SPL Assistant layer, D (you must assign a hotkey to open SPL Assistant layer first).

Cheers,

Joseph

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Afik Souffir
Sent: Friday, September 25, 2020 10:16 AM
To: nvda@nvda.groups.io
Subject: Re: [nvda] Nvda And SPL!

 

 

I'm asking the same question

 

How do you know the time in a playlist?

 

 

Afik

 

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Joseph Lee
Sent: Friday, September 25, 2020 7:29 PM
To: nvda@nvda.groups.io
Subject: Re: [nvda] Nvda And SPL!

 

Hi,

Yes, it is like starting from scratch with JAWS. There is a way to “label” encoders using NVDA through an add-on for StationPlaylist (expect a release announcement next week).

Cheers,

Joseph

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Thomas E Williamson, Senior
Sent: Friday, September 25, 2020 4:45 AM
To: nvda@nvda.groups.io
Subject: [nvda] Nvda And SPL!

 

Hello,

I am wanting to use nvda with station playlist 5.40.

Will this be like starting over again in turns of the key strokes from Jaws?

For example, when I open studio, my encoders do not display the names of the radio stations that I previously named.

or is there a tutorial that can assist in this matter?

Hope this make since.

Thanks for your help in advance!

Regards,

Thomas.

 

 

 


Re: Nvda And SPL!

Afik Souffir <afik.souffir@...>
 

How do you assign a keystroke for open it?

 

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Joseph Lee
Sent: Friday, September 25, 2020 8:19 PM
To: nvda@nvda.groups.io
Subject: Re: [nvda] Nvda And SPL!

 

Hi,

That’ll be SPL Assistant layer, D (you must assign a hotkey to open SPL Assistant layer first).

Cheers,

Joseph

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Afik Souffir
Sent: Friday, September 25, 2020 10:16 AM
To: nvda@nvda.groups.io
Subject: Re: [nvda] Nvda And SPL!

 

 

I'm asking the same question

 

How do you know the time in a playlist?

 

 

Afik

 

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Joseph Lee
Sent: Friday, September 25, 2020 7:29 PM
To: nvda@nvda.groups.io
Subject: Re: [nvda] Nvda And SPL!

 

Hi,

Yes, it is like starting from scratch with JAWS. There is a way to “label” encoders using NVDA through an add-on for StationPlaylist (expect a release announcement next week).

Cheers,

Joseph

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Thomas E Williamson, Senior
Sent: Friday, September 25, 2020 4:45 AM
To: nvda@nvda.groups.io
Subject: [nvda] Nvda And SPL!

 

Hello,

I am wanting to use nvda with station playlist 5.40.

Will this be like starting over again in turns of the key strokes from Jaws?

For example, when I open studio, my encoders do not display the names of the radio stations that I previously named.

or is there a tutorial that can assist in this matter?

Hope this make since.

Thanks for your help in advance!

Regards,

Thomas.

 

 

 


Re: Nvda And SPL!

 

Hi,

That’ll be SPL Assistant layer, D (you must assign a hotkey to open SPL Assistant layer first).

Cheers,

Joseph

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Afik Souffir
Sent: Friday, September 25, 2020 10:16 AM
To: nvda@nvda.groups.io
Subject: Re: [nvda] Nvda And SPL!

 

 

I'm asking the same question

 

How do you know the time in a playlist?

 

 

Afik

 

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Joseph Lee
Sent: Friday, September 25, 2020 7:29 PM
To: nvda@nvda.groups.io
Subject: Re: [nvda] Nvda And SPL!

 

Hi,

Yes, it is like starting from scratch with JAWS. There is a way to “label” encoders using NVDA through an add-on for StationPlaylist (expect a release announcement next week).

Cheers,

Joseph

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Thomas E Williamson, Senior
Sent: Friday, September 25, 2020 4:45 AM
To: nvda@nvda.groups.io
Subject: [nvda] Nvda And SPL!

 

Hello,

I am wanting to use nvda with station playlist 5.40.

Will this be like starting over again in turns of the key strokes from Jaws?

For example, when I open studio, my encoders do not display the names of the radio stations that I previously named.

or is there a tutorial that can assist in this matter?

Hope this make since.

Thanks for your help in advance!

Regards,

Thomas.

 

 

 


Re: Nvda And SPL!

Afik Souffir <afik.souffir@...>
 

 

I'm asking the same question

 

How do you know the time in a playlist?

 

 

Afik

 

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Joseph Lee
Sent: Friday, September 25, 2020 7:29 PM
To: nvda@nvda.groups.io
Subject: Re: [nvda] Nvda And SPL!

 

Hi,

Yes, it is like starting from scratch with JAWS. There is a way to “label” encoders using NVDA through an add-on for StationPlaylist (expect a release announcement next week).

Cheers,

Joseph

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Thomas E Williamson, Senior
Sent: Friday, September 25, 2020 4:45 AM
To: nvda@nvda.groups.io
Subject: [nvda] Nvda And SPL!

 

Hello,

I am wanting to use nvda with station playlist 5.40.

Will this be like starting over again in turns of the key strokes from Jaws?

For example, when I open studio, my encoders do not display the names of the radio stations that I previously named.

or is there a tutorial that can assist in this matter?

Hope this make since.

Thanks for your help in advance!

Regards,

Thomas.

 

 

 


Re: accessible disk imaging software.

Akash Kakkar
 

Object nav etc

On 9/25/2020 5:31 PM, Austin Pinto wrote:
what are the work arounds for magrum reflect?

On 9/25/20, Akash Kakkar <akash.diverse@gmail.com> wrote:
DriveSnapshot also doesn't have any incremental backup support.

I use it on regular basis

On 9/25/2020 2:39 PM, Stephen wrote:
Have you tried drive snapshot or image for windows?
They are extremely accessible.
I think drivesnapshot does full and differencial backup and image for
windows does full, differencial and increments.

----- Original Message -----
From: Austin Pinto <austinpinto.xaviers@gmail.com>
Reply-To: <nvda@nvda.groups.io>
To: <access-uk@freelists.org>
Sent: 9/25/2020 2:51:10 PM
Subject: [nvda] accessible disk imaging software.
________________________________________________________________________________

hi all.
i require an accessible disk imaging software that can backup and
restore windows 10 and data and also has incrimental and differencial
backup features.
i used to use active@disk image but it doesnt restore windows 10
properly.
please suggest











Re: Nvda And SPL!

 

Hi,

Yes, it is like starting from scratch with JAWS. There is a way to “label” encoders using NVDA through an add-on for StationPlaylist (expect a release announcement next week).

Cheers,

Joseph

 

From: nvda@nvda.groups.io <nvda@nvda.groups.io> On Behalf Of Thomas E Williamson, Senior
Sent: Friday, September 25, 2020 4:45 AM
To: nvda@nvda.groups.io
Subject: [nvda] Nvda And SPL!

 

Hello,

I am wanting to use nvda with station playlist 5.40.

Will this be like starting over again in turns of the key strokes from Jaws?

For example, when I open studio, my encoders do not display the names of the radio stations that I previously named.

or is there a tutorial that can assist in this matter?

Hope this make since.

Thanks for your help in advance!

Regards,

Thomas.

 

 

 


Re: Change Ringing: Practice and Theory

 

Damien,

          I can't help you out specifically, but I wanted to note that I've updated the topic to be fully descriptive, as Change Ringing is definitely "a thing of its own" and those who are into it will recognize it better.

          Since you're asking about what software related to change ringing is accessible with NVDA, that's entirely on-topic for the main group.  If the time comes where something is recommended and you want to discuss how to use that software, that topic should be started on the Chat Subgroup.
--

Brian - Windows 10 Pro, 64-Bit, Version 2004, Build 19041  

It’s hard waking up and realizing it’s not always black and white.

 

     ~ Kelley Boorn

 


Change Ringing: Practice and Theory

Damien Garwood <damien@...>
 

Hi all,
I know this is a rather specialised topic, but I'll ask anyway on the off chance.
1. Are there any change-ringers here who could advise me of the best ringing software that works with NVDA?
I'm looking for something that will enable me to learn new methods, so it can be either:
A. An app that plays a method, or prints the numbers out in CSV form
B. An app that requires you to ring a method, or follow calls, perhaps simulating a band and a conductor, and scores you on it.
2. I'm very interested into how change ringing compositions are made (being a musical composer myself). Apparently computers can generate them now, because it's very mathematical. I'd like to learn more about this, but whatever math (or maths, if you prefer) based articles I try and read, they're either covered with graphics, or a mysterious area of three or more spaces that mean absolutely nothing.
Someone suggested that Mathplayer was the way forward, but while that does interact with some of these areas, it didn't work with all of them, and the number of problems I had both understanding how to make sense of the information it provided when it did work, and then eventually uninstalling it, I'm a little cautious to start using it again.
Cheers.
Damien.

9161 - 9180 of 86645